Use this when you're ordering a replacement Bohn evaporator coil, speccing a new walk-in cooler or upright freezer, or pulling stock through one of the Bohn refrigeration distributors. It's written for distributors, installers, and maintenance techs who would rather spend fifteen minutes checking than two weeks fixing a return.
Seven steps. In the order I actually run them. If you have the paperwork in front of you, the whole thing takes about 15 minutes (20 if the nameplate is rusted, which it usually is).
A quick bit of context: I handle commercial refrigeration equipment orders for a regional distributor. Nine years in, I've personally made—and documented—14 significant ordering mistakes totaling roughly $6,200 in wasted budget, restock fees, and rushed freight. This checklist exists because of those 14 mistakes. Most of them happened in the first three years.
Every Bohn evaporator coil model number encodes something—coil family, fin spacing, capacity, voltage, defrost type, connection size. It's not decoration. I learned this in 2018 the expensive way: a customer asked for "the standard medium-temp coil" to replace a failed unit, I ordered based on the conversation, and the replacement arrived with the wrong defrost termination. The coil itself was fine. The termination kit was not.
Restock fee: $420. Plus a four-day delay while the correct unit shipped. Plus the customer watching a box of product slowly warm up.
What to do: photograph the old nameplate before anything else (decent lighting, straight on, no glare if you can manage it). Decode it against the current Bohn spec sheet—not a five-year-old one from the truck's glovebox. If the nameplate is illegible, get a measurement of the coil face and a photo of the connection stubs, then call the distributor. Do not guess.
Capacity, temperature difference, and airflow have to line up. A coil rated for a 10°F TD in a cooler is not automatically the right coil for a freezer running a tighter TD. Fin spacing matters too—freezers typically run tighter spacing than coolers, and using the wrong one means you'll be back in three months with a defrost problem that looks like a refrigerant problem but isn't.
Two quick filters I run every time:
One thing that trips up newer team members: if a customer starts asking heat pump vs furnace, they're talking about comfort heating, not refrigeration. That's a completely different system with different coils and different controls. Don't let the conversation drift. Confirm which system you're actually quoting before you touch a spec sheet.
Voltage, phase, defrost termination, fan delay, heater wattage. This is the step where "close enough" becomes a service call. I once approved a 208/230V single-phase coil against a three-phase circuit because the customer's maintenance guy said "it's all 230 anyway." It is not all 230 anyway.
Ask for the wiring diagram with the quote. Not after. With. If the distributor can't produce one, that's information you should have before you commit.
Physical fit is where experienced buyers still get burned. Width, height, depth, drain pan clearance, and—the one almost everyone forgets—service clearance for the fan guard and future coil cleaning. A unit that fits the opening but leaves no room to pull the fan assembly is a unit that gets installed once and hated forever.
The step most people skip: check the drain line route. Slope, heat tape if needed, and whether the new coil's drain connection points somewhere the old one didn't. On a tight retrofit, this is a 30-second check that prevents a 3-hour improvisation on install day.
"Lead time is two weeks" and "it ships on the 14th" are not the same sentence. One is a guess, the other is a commitment. Bohn refrigeration distributors vary widely in what they stock versus what they drop-ship, so the only number worth writing down is the one with a calendar date attached.
If the answer is vague, ask again. If it's still vague, assume it's longer than they said and plan accordingly. I'm not 100% sure this holds for every distributor, but in my experience the vaguest answers come from the busiest warehouses—and those are exactly the ones that slip.
This is the step I'd underline twice. When a coil fails on a Friday and the box is full of product, the relevant question is not "what's the cheapest freight"—it's "what's the cost of not knowing when it arrives."
In March 2024, we paid about $380 extra for a guaranteed two-day freight window on a replacement coil. The alternative was a customer's upright freezer inventory—roughly $11,000 of frozen product—sitting in a box with no confirmed ETA. The $380 wasn't for speed. It was for the certainty that let the customer stop calling me every two hours.
After getting burned twice by "it should be there Tuesday" promises that turned into Thursday, we started budgeting for guaranteed delivery windows on any order where a deadline is real. Not every order. But any order where the customer's product is on the line.
Last step, and the one that catches the small stuff. Defrost timer or control board. Fan guards. Mounting brackets. Wiring diagram and AHRI-certified capacity data for the file. If the customer's inspector wants documentation, you want to have it before the coil is on the roof, not after.
Run this as a literal list against the quote. Not from memory. Memory is how I ended up with a coil that arrived without the fan guard I was sure I'd ordered—turns out I'd ordered it on a separate line and the warehouse consolidated the shipment incorrectly. Nobody's fault, technically. Still cost a week.
Trusting a corroded nameplate. If half the digits are gone, measure and photograph. A wrong model number is worse than no model number because it feels like certainty.
Ignoring the air side. Everyone checks refrigerant and electrical. Almost nobody checks whether the coil fins are accessible for cleaning. Treat the air-side filter the way you'd treat the K&N air filter in your service truck—it's the thing that quietly degrades performance until someone finally looks at it. If the new coil leaves no access for cleaning, you've just installed a future capacity complaint.
Ordering on Friday afternoon. Not a technical rule. Just a pattern I've noticed across nine years and 14 mistakes. Friday orders get entered Monday, and Monday is when everyone else's Friday orders get entered too.
Letting the customer define the spec. They know their box. They don't necessarily know their TD, their fin spacing, or their defrost termination. Take their operational requirements and translate them into a model number yourself. That translation is the job.
Photograph the nameplate, decode the nomenclature, match capacity and refrigerant, confirm the electrical and controls, measure the opening and the drain route, get a ship date, decide on freight certainty, then check the accessories line by line. Seven steps. Fifteen minutes. It's cheaper than a restock fee, and considerably cheaper than a warm freezer full of product.